Unable to connect to VPN from Oracle VM VirtualBox

Got a problem with Viscosity or need help? Ask here!

melmat

Posts: 1
Joined: Fri Jun 10, 2016 11:07 pm

Post by melmat » Fri Jun 10, 2016 11:35 pm
Hi,

I have Oracle VM VirtualBox installed on my laptop running Windows 7 64bit with the network adaptor set to bridge mode. I can connect to the VPN outside the VirtualBox and Map Network drives, ping servers etc..But inside my VirtualBox i cant connect to the VPN to map drives etc..I have tried several configs on the Network settings for VirtualBox (Nat) Nat Network, Host Only, but cant connect.. I have internet access on both enviroments. Also i have static address for both enviroments on the same network. Here is my log. Thanks for any help.

Jun 11 1:29:47 AM: State changed to Disconnecting
Jun 11 1:29:47 AM: State changed to Disconnected
Jun 11 1:29:55 AM: State changed to Connecting
Jun 11 1:29:55 AM: Viscosity Windows 1.6.4 (1448)
Jun 11 1:29:55 AM: Running on Microsoft Windows 7 Enterprise
Jun 11 1:29:55 AM: Bringing up interface...
Jun 11 1:29:55 AM: Checking reachability status of connection...
Jun 11 1:29:55 AM: Connection is reachable. Starting connection attempt.
Jun 11 1:29:55 AM: OpenVPN 2.3.11 Windows-MSVC [SSL (OpenSSL)] [LZO] [PKCS11] [IPv6] built on May 11 2016
Jun 11 1:29:55 AM: library versions: OpenSSL 1.0.2h 3 May 2016, LZO 2.09
Jun 11 1:30:00 AM: WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this
Jun 11 1:30:04 AM: SIGUSR1[soft,private-key-password-failure] received, process restarting
Jun 11 1:30:04 AM: State changed to Connecting
Jun 11 1:30:14 AM: SIGUSR1[soft,private-key-password-failure] received, process restarting
Jun 11 1:30:14 AM: State changed to Connecting
Jun 11 1:30:20 AM: WARNING: normally if you use --mssfix and/or --fragment, you should also set --tun-mtu 1500 (currently it is 1400)
Jun 11 1:30:20 AM: UDPv4 link local (bound): [undef]
Jun 11 1:30:20 AM: UDPv4 link remote: [AF_INET]222.154.227.96:1194
Jun 11 1:30:21 AM: [10.1.1.7] Peer Connection Initiated with [AF_INET]222.154.227.96:1194
Jun 11 1:30:23 AM: do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0
Jun 11 1:30:23 AM: open_tun, tt->ipv6=0
Jun 11 1:30:23 AM: TAP-WIN32 device [Mathew-TO-IPCop] opened: \\.\Global\{571B7287-9434-4A5C-8ED3-BDC3D797B5BD}.tap
Jun 11 1:30:23 AM: Notified TAP-Windows driver to set a DHCP IP/netmask of 10.96.216.22/255.255.255.252 on interface {571B7287-9434-4A5C-8ED3-BDC3D797B5BD} [DHCP-serv: 10.96.216.21, lease-time: 31536000]
Jun 11 1:30:23 AM: Successful ARP Flush on interface [21] {571B7287-9434-4A5C-8ED3-BDC3D797B5BD}
Jun 11 1:30:28 AM: Initialization Sequence Completed
Jun 11 1:30:29 AM: WARNING: Split DNS is being used however no DNS domains are present. The DNS server/s for this connection may not be used. For more information please see: https://www.sparklabs.com/support/kb/ar ... e-present/
Server - 202.27.156.72:53; Lookup Type - Split; Domains - None
Server - 192.168.81.254:53; Lookup Type - Any; Domains - None
Server - 192.168.81.254:53; Lookup Type - Any; Domains - None

Eric

User avatar
Posts: 1146
Joined: Sun Jan 03, 2010 3:27 am

Post by Eric » Tue Jun 14, 2016 12:00 pm
Hi melmat,

Please note this is a public forum and you may wish to email us this information instead.

Could you please post a copy of your outputs from ipconfig -all and route print. To get these, go to Start, search and open Command Prompt, then type in each command.

When trying to map drives, are you doing this via DNS or the drives IP address? Please note the following in the log:
WARNING: Split DNS is being used however no DNS domains are present. The DNS server/s for this connection may not be used. For more information please see: https://www.sparklabs.com/support/kb/ar ... e-present/

Regards,
Eric
Eric Thorpe
Viscosity Developer

Web: http://www.sparklabs.com
Support: http://www.sparklabs.com/support
Twitter: http://twitter.com/sparklabs
2 posts Page 1 of 1